Home » Buttwelding Fittings » ASME B16.9 6IN SCH40 A234WPB Butt Weld Tee

ASME B16.9 6IN SCH40 A234WPB Butt Weld Tee

It is used to handle any high or low weight fluid flow through the tee.Reducing tee is a kind of pipe fitting whose branch size is smaller than the size of pipeline parts. It is used for main pipe string accessories, solvent welding accessories, side outlet and conflicting soluble welding accessories.

Rated 5/5 based on 428 customer reviews
Share:
Content

Production Description

ASME B16.9 6IN SCH40 A234WPB Butt Weld Tee Pipe Fittings is a T-shaped pipe fittings that has three branches, normally has two forms with Equal Tee and Reducing Tee, both are used to divide the pipelines to adjust the flow rate and change the direction.Since the distance between the branch pipe and the pipe run is the same, an equivalent tee is used.

Steel pipe tee

Steel tee is a T-shaped pipe fitting with three branch pipes. It is used to divide pipes to adjust flow and change direction.

Equal Tee

Equal diameter tee, also known as straight tee, the branch diameter of the tee is the same as the pipe diameter of the tee.

Reducing Tee

The reducing tee has two outlets cut at 90 degrees with the main pipe, and the size of the branch pipe is smaller than the port of the pipeline

Production Advantages

  • Good general corrosion resistance and high strength
  • Good sulfide stress corrosion resistance
  • Resistance to chloride pitting and crevice corrosion
  • Higher resistance to chloride stress corrosion cracking
  • Easy to weld and conform

Specificaton of 8IN SCH40 Stainless Steel Butt Weld Tee Pipe Fittings

Size Range 1/2″ – 80″ / DN15 – 2000
Thickness Schedule SCH 10,SCH 10S, SCH 20, SCH 40,SCH 40S, STD, XS,SCH 80, SCH 80S, SCH 100, SCH 120, SCH 160, XXS
China Standard GB/T12459, GB/T13401, HG/T21635/21631, SH3408/3409
America Standard ANSI / ASME B16.9 / MSS SP 43
apan Standard JIS B2311/2312/2313
Europe Standard EN10253
Carbon Steel Q235, 20#, 35#, 45#, 20G,ASTM A234 WPB/WPC
Low Temp Carbon Steel Q345B, 16Mn, ASTM A420 WPL6
Pipeline Steel ASTM A860 WPHY 42 / 46 / 56 / 60 / 65
Alloy Steel ASTM A234 WP11 / WP12 / WP 5 / WP9 / WP91 / WP92,15CrMoG, 12Cr1MoVG, 12Cr5Mo, 1Cr5Mo, Cr9Mo, 10CrMo910, 12CrMo4-5
Stainless Steel ASTM A403 WP304/304L/304H, 316/316L, 310S, 321, 317,347,904L
Duplex Stainless Steel ASTM A815 S32205, S31803, 32750, 32760

Butt Weld Tee Pipe Fittings Dimensions and Weight Chart

Nominal Size Outside Diameter at Bevel Center to End
DN NPS OD1×OD2 C M
15 1/2 21.3 25 25
20 3/4 26.7 29 29
25 1 33.4 38 38
32 11/4 42.2 48 48
40 11/2 48.3 57 57
50 2 60.3 64 64
65 21/2 73.0 76 76
80 3 88.9 86 86
90 31/2 101.6 95 95
100 4 114.3 105 105
125 5 141.3 124 124
150 6 168.3 143 143
200 8 219.1 178 178
250 10 273.0 216 216
300 12 323.8 254 254
350 14 355.6 279 279
400 16 406.4 305 305
450 18 457.0 343 343
500 20 508.0 381 381
550 22 559.0 419 419
600 24 610.0 432 432
650 26 660.0 495 495
700 28 711.0 521 521
750 30 762.0 559 559
800 32 813.0 597 597
850 34 864.0 635 635
900 36 914.0 673 673
950 38 965.0 711 711
1000 40 1016.0 749 749
1050 42 1067.0 762 711
1100 44 1118.0 813 762
1150 46 1168.0 851 800
1200 48 1219.0 889 838
1300 52 1321.0 965 914
1400 56 1422.0 1041 965
1600 64 1626.0 1194 1092
1700 68 1727.0 1270 1168
1800 72 1829.0 1320 1245
1900 76 1930.0 1422 1320
2000 80 2032.0 1499 1397

Production Material

ASTM A234 WPB is a Standard Determination for steel pipe fittings that incorporates carbon and alloy steel material for direct and high-temperature administrations. ASTM A234 WPB Sch 40 Fittings covers carbon steel fittings of welded and seamless development secured by the foremost later revision of ASME B16.9, B16.11, MSS-SP-79, MSS-SP-83, MSS-SP-95, and MSS-SP-97. ASTM A234WPB 12IN SCHSTD 45Deg Elbow to boot exceedingly corrosion-resistant has low string contact and profitable where high alloyed steel is required. We are one among the unmistakable suppliers and merchants of these premium qualities ASTM A234 WPB Seamless Pipe Fitting, which in addition utilized in Manufacturing plants, Troublesome planning firms, Steel plants, and so on.

ASTM A234 Mechanical Properties
Tensile and Yield Strength ASTM A234 for Carbon and Alloy Steel Fittings WPB WPC,
WP11-CL2
WP11-CL1,
WP22-CL1
WP5-CL1
WP9-CL1
WP11-CL3,
WP22-CL3
WP5-CL3
WP9-CL3
WP91
Tensile strength, minimum unless a range is given ksi (MPa) 60 (415) 70 (485) 60 (415) 75 (520) 90(620)
Yield strength, min ksi (MPa) (0.2% offset or 0.5% extension under-load) 35 (240) 40 (275) 30 (205) 45 (310) 60(415)

 

Elongation ASTM A234 for Carbon and Alloy Steel Fittings WPB, WPC, WP11, WP22 WP91 WP92 WPR and WP24
Longitud. Transverse Longitud.  Transverse Longitud.  Transverse
Standard
round specimen, or small proportional specimen, min % in 4 D
22 14 20 13 20
Rectangular specimen for wall thickness 5/16″ and over, and
for all small sizes tested in full section; min % in 2 in.
30 20 28
Rectangular specimen for wall thickness less than 5/16″;
min % in 2 in (1/2″ wide specimen)
B B B

 

Wall Thickness Grades
WPB, WPC, WP11, WP22 WPR WP91 WP92
IN MM Longitud. Transverse Longitud. Transverse
5/16(0.312) 7.94 30 20 28 20
9/32(0.281) 7.14 28.5 19 26.5 19
1/4(0.250) 6.35 27 18 25 18
7/32(0.219) 5.56 25.5 23.5 17
3/16(0.188) 4.76 24 22 16
5/32(0.156) 3.97 22.5 20.5 15
1/8(0.125) 3.17 21 19 14
3/32(0.094) 2.38 19.5 17.5 13
1/16(0.062) 1.59 18 16 12

 

ASTM A234 Chemical Composition
Chemical composition of ASTM A234  Fittings
Grade C Mn P max S max Si Cr Mo Ni Cu OTHERS
WPB(1.2.34.5) 0.30max 0.29-1.06 0.05 0.058 0.10min 0.4max 0.15max 0.4max 0.4max V0.08max
WPC(2.3.4.5) 0.35max 0.29-1.06 0.05 0.058 0.10min 0.4max 0.15max 0.4max 0.4max V0.08max
WP1 0.28max 0.30-0.90 0.045 0.045 0.10-0.50 0.44-0.65
WP12.CL1 0.05-0.20 0.30-0.80 0.045 0.045 0.60max 0.8-1.25 0.44-0.65
WP12 CL2 0.05-0.20 0.30-0.80 0.03 0.045 0.60max 0.8-1.25 0.44-0.65
WP11CL1 0.05-0.15 0.30-0.60 0.04 0.03 0.50-1.00 1.00-1.5 0.44-0.65
WP11CL2 0.05-0.20 0.30-0.80 0.04 0.04 0.50-1.00 1.00-1.5 0.44-0.65
WP11CL3 0.05-0.20 0.30-0.80 0.04 0.04 0.50-1.00 1.00-1.5 0.44-0.65
WP22CL1 0.05-0.15 0.30-0.60 0.04 0.04 0.50max 1.00-1.5 0.44-0.65
WP22CL3 005-0.20 0.30-0.60 0.04 0.04 0.50max 1.00-1.5 0.44-0.65
WP5CL1 0.05-0.20 0.30-0.60 0.04 0.04 0.50max 1.9-2.6 0.87-1.13
WP22CL3 0.05-0.20 0.30-0.60 0.04 0.04 0.50max 1.9-2.6 0.87-1.13
WP5CL1 0.05-0.15 0.30-0.60 0.04 0.03 0.50max 4.0-6.0 0.44-0.65
WP5CL3 0.15max 0.30-0.60 0.04 0.03 0.50max 4.0-6.0 0.44-0.65
WP9CL1 0.15max 0.40-1.06 0.03 0.03 1.00max 1.0max 0.90-1.10
WP9CL3 0.15max 0.30-0.60 0.03 0.03 1.00max 8-10.0 0.90-0.10
WPR 0.20max 0.40-1.06 0.045 0.05 1.60-2.24 0.75-1.25
WP91 0.08-0.12 0.30-0.60 0.02 0.01 0.20-0.50 8.0-9.5 0.85-1.05 0.40max V 0.18- 0.25
Nb 0.06-0.10
N 0.03-0.07
Al 0.02 max(6)
Ti 0.01 max(6)
Zr 0.01 max(6)
WP911 0.09-0.13 0.30-0.60 0.02 0.01 0.10-0.50 8.0-9.5 0.90-1.10 0.40max V 0.18-0.25
Nb 0.060-0.10
N 0.04-0.09
Al 0.02 max(6)
B 0.0003-0.006
W 0.90-1.10
Ti 0.01 max(6)
Zr 0.01 max(6

Applications

  • Water supply facilities
  • Food industrial pipelines
  • Chemical industrial pipelines
  • Electronic industrial pipelines
  • Air conditioning facility pipelines
  • Agriculture and garden production transportation
  • Pipeline network for solar energy facility

Packing Dtails

BW Reducing Tee Carbon Steel Fittings

Inquiry


    More Buttwelding Fittings