Welding neck flanges 300# ASTM A105N B16.5

150LB SO Flange is the lowest pressure flange in flanges.High Pressure Forged Flange have many pressures:CL150, CL300, CL600, CL900, CL1500, CL2500.

Socket weld (SW) flange is a type of forged flanges,these flanges can socket and wedled with pipes,you could find the flanges specifications in the content below.Stainless steel flanges are popular because the stainless steel has great corrosion resistance so that these flanges can used in some corrosive environments.

What is a blind flang,what about its specification and advantage.

The slip-on flange is a simple and excellent alternative to a weld neck as it does not have a weld bevel, and therefore allows the pipe to be adjusted in length relative to its position of the flange. The bore of the slip on will give ample amount of space for the matching pipe.

l. Large diameter flat welding flange has less high-pressure suitability compared to its weld neck counterpart. The basic ring style is suitable for the occasion of low pressure. The butt weld category of the flange is known as a weld neck flange. It suits the occasion of high temperature and pressure as defined in the ASME B16.47 code. Large diameter flanges are widely popularized and used in the sewage treatment industry, wind power industry, chemical industry, and machinery industry.

A105 WN flange is a carbon steel flange according to ASME B16.5.STD is represents the thickness of the flange.Flanges have many pressures:CL150, CL300, CL600, CL900, CL1500, CL2500.Flanges have five face types:RF RTJ FF MF TG.

Slip ons in higher pressure classes are often made with the height of a lap joint for a better connection. If the hub height is not a concern and a lap joint is not readily available, customers will sometimes opt for a slip on made to a lap joint style with a machined hub.

These pipe flanges are attached by inserting the pipe into the socket end and applying fillet weld around the top. This allows for a smooth bore and better flow of the fluid or gas inside of the pipe. The connection with the pipe is done with 1 fillet weld, at the outside of the flange. But before welding, a space must be created between flange or fitting and pipe.

ASTM A182 F316 is a popular grade for stainless steel in American Standard.Stainless steel fittings are popular because of the an-ti corrosive function.Stainless steel pipe fittings can used over 50 years.

Stainless steel lap joint flange is always used with lap joint stub end (a kind of butt welded fitting).A182 F304 forged flanges have great anti-corrosive function,flanges in this material have longer using years than other materials.

Flanges are usually welded or screwed. Flanged joints are made by bolting together two flanges with a gasket between them to provide a seal. Large diameter flat welding flange has less high-pressure suitability compared to its weld neck counterpart. The basic ring style is suitable for the occasion of low pressure.

Socket weld flange can socket with the end of pipe,and welding on the pipe.Stainless steel flanges are popular because of the an-ti corrosive function.Stainless steel pipe fittings can used over 50 years.

Forged Steel Flange are attached by inserting the pipe into the socket end and applying fillet weld around the top. This allows for a smooth bore and better flow of the fluid or gas inside of the pipe.

Alloy Steel: ASTM A182 F11 / 12 / 5 / 9 / 91 / 92
Stainless Steel: ASTM A182 F304/304L/304H, 316/316L, 321, 310S, 317,347,904L, 1.4404, 1.4437.

The slip-on flange is a simple and excellent alternative to a weld neck as it does not have a weld bevel, and therefore allows the pipe to be adjusted in length relative to its position of the flange. The bore of the slip on will give ample amount of space for the matching pipe.

Socket Weld Flange contain a shoulder on the flange inside that acts as a guide to set the depth at which the pipe is welded to the flange.

orged steel flange is a disc-shaped piece of equipment used to connect a pipe to fittings or valve or other component to form a pipework system. Usually flange has been attached to pipe or tube end to, and then a gasket is inserted in the middle to form a seal. Finally they are joined together with bolts and nuts.

What is a Weld Neck(WN) Flange and what about its specification and advantages.

150 LB blind flange is a flange similar to plug.BL flanges are used to close the pipe system.ASTM A105 forged flange is carbon steel flange in American Matel Standard.

900LB slip on flange can slip on the pipes and welded with the pipes.Stainless steel flanges are popular because of the an-ti corrosive function.Stainless steel flange can used over 50 years.Flanges have many pressures:CL150, CL300, CL600, CL900, CL1500, CL2500.

Class 300 LAPJ flanges are used with lap joint stub end.The pressures for ASME B16.5 forged flanges including 150LB,300LB,600LB,900LB,1500LB12500LB.

Slip on flange, also called SO flange. It’s a kind of flange slides over the pipe with internal design is slightly larger than the pipe. Since the inner diameter of the flange is slightly larger than the outer diameter of the pipe, the SO flange can be directly connected to equipment or pipe by fillet weld at the top and bottom of the flange. It is used to insert the pipe into the inner hole of the flange.

There are varies advantages of stainless steel flange:
Resistant to corrosion and staining
Low maintenance
Bright familiar luster
Steel Strength

Class 1500 SO flange Flanges have many pressures:CL300, CL600, CL900, CL1500, CL2500.Flanges have five face types:RF RTJ FF MF TG. Slip on flanges can slip on the pipes and welding with the pipes.

A flange is a category of gasket made to fix two sections of pipe together, or act as a removable plug at the end of a single pipe. All flanges are round disks with holes for bolts around the rim, but the commonalities end there. a projecting flat rim used for strengthening or attachment.

Class 600 WN flange is a high pressure flange.Flanges have many pressures:CL300, CL600, CL900, CL1500, CL2500.ASME B16.5 is the American Standard for flanges.Flanges have five face types:RF RTJ FF MF TG.